PUBLIC NOTICE No. 51(RE-99) / 1997-2002 Dated 1st March, 2000

Attention is invited to Paragraph 7.8 of the Export and.import Policy'1997-2002, as amended and Paragraphs 7.8 and 7.10 of the Handbook of Procedures, Vol.1, 1997-2002, as amended and also to the Handbook of Procedures, Vol.2, 1997-2002, as amended from time to time.

In exercise of the powers conferred under Paragraph 4.11 of the Export and Import Policy 1997-2002, as amended, the Director General of Foreign Trade hereby makes the following amendments / modifications and additions in the Handbook of Procedures, Vol.2, 1997-2002, as amended.

In the statement of Standard Input Output Norms as contained in the Handbook of Procedures, Vol.2, 1997-2002, as amended, amendments / corrections at appropriate places as mentioned in Annexure "A" to this Public Notice shaLl be made.

In the statement of Standard Input Output Norms, following additions shall be made at appropriate places as mentioned below:-

CHEMICALS AND ALLIED PRODUCTS
After the existing entry at SI.No.A-2386, the new entries from SI.No.A-2387 to A-2402 shall be added as per Annexure "B" to this Public Notice.

ENGINEERING PRODUCTS
After the existing entry at SI.No.C-1500, the new entries from SI.No.C-1501 to C-1517 shall be added as per Annexure "C" to this Public Notice.

This issues in Public interest.

Sd/-
(N.L. Lakhanpal)
Director General of Foreign Trade

Annexure "A" to the
Public Notice No.51
Dated: 01/03/2000

AMENDMENTS/CORRECTIONS

Sl.No.	Page No.	Reference	Amendments/Corrections
(1)	(2)	(3)	(4)
1.	10	Chemicals & Allied Products Sl.No.A35	The description of the import item at Sl. No. 4 shall be amended (without any change in the quantity) to read as under:- "BIS TRIMETHYL SILYL UREA"
2.	12	Chemicals & Allied Products Sl.No.A48	The description and quantity of the import item at Sl. No. 1(a) shall be amended to read as under:-
			"PIPERAZINE WATER SOLUTION (ON 100% BASIS)	2.21 kg."
3.	24	Chemicals & Allied Products Sl.No.A111	The description of the import item at Sl. No. 4 shall be amended (without any change in the quantity) to read as under:- "BIS TRIMETHYL SILYL UREA"
4.	35	Chemicals & Allied Products Sl.No.A173	The description of the import item at Sl. No. 4 shall be amended (without any change in the quantity) to read as under:- br>"SODIUM DIHYDRO BIS {2 METHOXY ETHOXY ALUMINATE 70% IN ACTIVE TOLUENE}".
5.	49	Chemicals & Allied Products Sl.No.A274	After import item No. 4 the following item with quantity shall be added:- "ACETONE - 1.22 kg/kg"
6.	53	Chemicals & Allied Products Sl.No.A307	The description and quantity of the import item at Sl. No. 1 shall be amended to read as under:-
			"PIPERAZINE WATER SOLUTION (ON 100% BASIS)	1.67 kg."
7.	53	Chemicals & Allied Products Sl.No.A308	The description and quantity of the import item at Sl. No. 1 shall be amended to read as under:-
			"PIPERAZINE WATER SOLUTION (ON 100% BASIS)	1.46 kg.".
8.	4	Chemicals & Allied Products Sl.No.A686 ( As amended vide P.N. No. 37 dt. 01.11.99)	The description of the import item at Sl. No. 2 shall be amended (without any change in the quantity) to read as under:- "Cobalt Chloride hexa hydrate".
9.	130	Chemicals & Allied Products Sl.No.A938	The norm covered by this entry shall be substituted by the following:-

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
A938	Solvent Black 5	1 kg	1. Aniline	1.070 kg
			2. Nitrobenzene	0.305 kg
10.	130	Chemicals & Allied Products Sl.No.A939	The norm covered by this entry shall be substituted by the following:-

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
A939	Solvent Black 7	1 kg	1. Aniline	1.070 kg
			2. Nitrobenzene	0.305 kg
11.	271	Chemicals & Allied Products Sl.No.A2017	The description of the import item at Sl. No. 4 shall be amended (without any change in the quantity) to read as under:- "BIS TRIMETHYL SILYL UREA"
12.	273	Chemicals & Allied Products Sl.No.A2027	The norm covered by this entry shall be substituted by the following:-

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
A2027	Cefotaxime Sodium Sterile USP/BP	1 kg	1. 7-ACA	0.741 kg.
			2. Mercapto Benzo Thiazole-4-YL-2 (2-Amino Thiazolyl) Methoxy Imino Acetate (MAEM) OR	1.025 kg.
			i) Ethyl Aceto Acetate	0.965 kg.
			ii)Potassium Carbonate	1.44 kg.
			iii)Bromine	0.76 kg.
			iv)Triphenyl Phosphine	1.23 kg.
			v)Vulkacit Acid	1.49 kg.
			3. Methylene Chloride	5.20 kg.
			4. Isopropyl Alcohol	4.68 kg.
			5. Acetone	1.51 kg.
			6. Methanol	5.23 kg.
			7. Formic Acid	1.19 kg.
			8. Triethyl Amine	0.41 kg.
			9. Ethyl Hexanate/ 2-Ethyl Hexanoic acid	0.40 kg.

13.	15	Chemicals & Allied Products Sl.No.A2263 ( As amended vide Public Notice No. 26 dt. 04.08.99)	The description of the import item at Sl. No. 6 shall be amended (without any change in the quantity) to read as under:- "2-METHOXY PROPANE"
14.	17	Chemicals & Allied Products Sl.No.A2293 ( As amended vide Public Notice No. 37 dt. 01.11.99)	The quantity of the import item at Sl. No. 1 shall be corrected to read as under:- "0.0525 kg. instead of 0.525 kg".
15.	23	Chemicals & Allied Products Sl.No.A2339 (Introduced vide Public Notice No. 46 dt. 3.1.2000)	The norm covered by this entry shall be deleted.
16.	25	Chemicals & Allied Products Sl.No.A2352 (Introduced vide Public Notice No. 46 dt. 3.1.2000)	The description of the import item at Sl. No. 1 indicated as "( Tin Oxide )" shall be deleted.
17.	335	Electronics Products Sl.No.B111	1. The description of the import item at Sl. No. 16 shall be amended (without any change in the quantity) to read as under:- "Inductor/Cell" 2. The description of the import item at Sl. No. 22 shall be amended (without any change in the quantity) to read as under:- "Adhesive/non-adhesive front housing logo label paper or Adhesive/non-adhesive plastic labels". 3. The description of the import item at Sl. No. 5 shall be amended (without any change in the quantity) to read as under:- "Hardware Parts for pagers:- (i) Screws - Net+2% (ii) Shield - Net+2% (iii)Lanyard - Net+2%" 4. The description of the import item at Sl. No. 23 shall be amended (without any change in the quantity) to read as under:- "Double Sided ESD Tape". 5. After import item No. 46 the following item with quantity shall be added:- "47. Boots - Net+2% 48. Battery contacts - Net+2% 49. Pads - Net+2% 50. Bracket - Net+2% 51. Back up battery - Net+2% 52. Lens - Net+2% 53. Light Wedge - Net+2% 54. Snubber - Net+2% 55. Latch - Net+2%".
18.	401	Engineering Products Sl.No. C188	The description of import item at Sl. No. 1(a) shall be amended to read as:- "Super Enamelled Copper Wire / Copper Wire Rod".
19.	402	Engineering Products Sl.No. C189	The description of import item at Sl. No. 1(a) shall be amended to read as:- "Super Enamelled Copper Wire / Copper Wire Rod".
20.	410	Engineering Products Sl. Nos. C208 to C-212	The descriptions of import item at Sl. No. 1 shall be amended to read as:- "CRGO Steel Sheets/ CRNGO Steel Sheet".
21.	529	Engineering Products Sl. Nos. C621	The description of the export item shall be amended to read as:- "Crowns made of tin free steel/Tin plate prime with dry blend lining printed instead of Crawn made of Tin Free sheet/Tin plate prime with double ring dry blend lining printed
22.	644	Engineering Products Sl.No.C1175	The norm covered by this entry shall be substituted by the following:-

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
C1175	Condensor/Evaporator Coils used as Heat exchangers for Airconditioning and Refrigerator purpose.	1 kg	1. Copper Tubes refrigeration Quality-Dia 1/4"-1/2"	1.05 kg/kg content in export product
			2. Aluminium Fin Stock thickness 0.10 mm to 0.20 mm	1.10 kg/kg content in export product
			3. Brazing materials	0.5% of FOB value
			4. U Bends and Tripods	net to net.
23.	667	Engineering Products Sl.No. C1327	Norm covered by this entry shall be substituted by the following:-

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
C1327	Auto Transformer ( variable voltage ) (a) upto 30 KVA 1 phase or 90 KVA 3 phase	1 No.	1. CRGO steel laminations/ sheets/ Coil/Slits/Cuts	2.64 kg. per KVA
			2. Copper winding wires/strips/Wire bars/Wire Rods/Cathodes	0.78 kg. per KVA
			3. Carbon in brushes/Blocks/ Rollers	5.0 Cub. Cm. Per KVA
			4. Brush Holder assembly	Net to net
			5. Servo Motor Magnets for Motors	Net to net
	(b) Above 30 KVA 1 phase or 90 KVA 3 phase and upto 130 KVA 1 phase or 390 KVA 3 phase		1. CRGO steel laminations/sheets/ Coil/Slits/Cuts	2.11 kg. per KVA
			2. Copper winding wires/strips/Wire bars/Wire Rods/ Cathodes	0.77 kg. per KVA
			3. Carbon in brushes /Blocks/ Roller	5.0 Cub. Cm. Per KVA
			4. Brush Holder assembly	Net to net
			5. Servo Motor Magnets for Motors	Net to net
	(c) above 130 KVA 1 phase or 390 3 phase		1. CRGO Steel laminations/ sheets/Coil/Slits/Cuts	1.71 kg. per KVA
			2. Copper winding wires/strips/Wire bars/Wire Rods/Cathodes	0.6 kg. per KVA
			3. Carbon in brushes/Blocks/ Rollers	5.0 Cub. Cm. Per KVA
			4. Brush Holder assembly	Net to net
			5. Servo Motor Magnets for Motors	Net to net

24.	672	Engineering Products Sl.No. C1343	The quantity of the import item ABS Granules at Sl. No. 8 shall be amended to read as :- "1.05 kg/kg content in the export product instead of 120 kg".
25.	13	Engineering Products Sl.No.C1391 (As amended vide Public Notice No. 50 dated : 02/02/2000)	A. COMPONENTS The description and quantity of import item at Sl. No. 7 shall be amended to read as under:- "7. Outer Gasket or Synthetic Rubber (Buna/NBR) 700 gms for 1000 Nos.Gasket".
31.	790	Plastic Products Sl.No.H5	In the import item at S.No. 8, after the description BHT, the following shall be added without any change in quantity:- "IRGONOX - 1076".
27.	32	Miscellaneous Products Sl.No.K122 (Introduced vide Public Notice No. 46 dated : 03/01/2000)	CORRIGENDUM The quantity of import item at Sl. No. 4 shall be corrected as under:- "0.166 Sq. Mtrs."
28.	33	Miscellaneous Products Sl.No.K123 (Introduced vide Public Notice No. 46 dated : 03/01/2000)	CORRIGENDUM The quantity of import item at Sl. No. 4 shall be corrected as under:- "0.174 Sq. Mtrs."
29.	35	Miscellaneous Products Sl.No.K124 (Introduced vide Public Notice No. 46 dated : 03/01/2000)	CORRIGENDUM The quantity of import item at Sl. No. 4 shall be corrected as under:- "0.183 Sq. Mtrs."

Annexure "B" to the
Public Notice No.51
Dated: 01/03/2000

CHEMICALS AND ALLIED PRODUCTS

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
A2387	FMOC-ONSU (9-Fluorenyl Methyl Succinimidyl Carbonate)	1 kg	1. Fluorene	2.14 kg.
			2. Dimethyl Formamide	3.22 kg.
			3. N-Hydroxy Succinimide OR	1.12 kg.
			3. a) Succinahydride	1.60 kg.
			3. b) Hydroxylamine HCI.	1.28 kg.
			4. Ethyl Formate	1.91 kg.
A2388	CIPROFLOXACIN LACTATE MONOHYDRATE	1 kg	1. 2,4 Dichloro 5-Fluoro Acetophenone	1.54 kg.
			2. Dimethyl Carbonate	1.74 kg.
			3. Sodium Hydride	0.52 kg.
			4. Dimethyl Formamide	1.74 kg.
			5. Potassium Carbonate	1.14 kg.
			6. Cyclo Propyl Amine	0.30 kg.
			7. Piperazine Anhydride	0.798 kg.
A2389	2-Mercapto-5-Methoxy Benzimidazole	1 kg	1. Para Anisidine	1.28 kg.
			2. Ethyl Acetate	1.00 kg.
			3. N-Butyl Alcohol	0.51 kg.
A2390	Trinonyl Phenyl Phosphite (TNPP)	1 kg	1. Nonyl Phenol	0.9343 kg.
			2. Tri Iso Propanol Amine	0.0057 kg.
A2391	Inhalers	1 No.	1. Relevant Bulk Drug (as per Drug Manufacturing Licence)	Net to net
			2. Aerosol Valves of relevant size	1.01 nos.
			3. Aluminium Can of relevant size	1.01 nos.
			4. Actuator with dust covers/ cap of relevant size	1.01 nos.
A2392	3:4 Diamino Benzophenone	1 kg	1. Para Chloro Toluene	0.953 kg.
			2. Dimethyl formamide	0.200 kg.
			3. Methanol	0.250 kg.
A2393	3- Carbamoyl-4 Methyl- 6- Hydroxy N-Ethyl -2 Pyridone	1 kg	1. Ethyl Gyana Acetate	0.854 per kg.
			2. Aceto Acetic Methyl Ester	0.876 per kg.
			3. Mono Ethyl Amine 70%	0.486 per kg.
A2394	Disperse Red 91 100% dyes content	1 kg	1. 1-Amino Anthraquinone	0.935 kg.
			2. 1:6 Hexanediol	0.410 kg.
A2395	Vat Brown 1 (Vat Brown BRCDP) (Dye content 98%)	1 kg	1. Anthraquinone	1.240 kg
			2. Quinizarine	0.552 kg
			3. Pyridine	0.380 kg.
			4. Nitrobenzene	1.050 kg.
			5. Caustic Soda flakes	3.190 kg
A2396	Direct Yellow 11 (50% dye content)	1 kg	1. Para Nitro Toluene	0.374 kg.
A2397	Geranyl Nitrite (Min. purity 98%)	1 kg	1. Citral	1.333 kg.
			2. Hydroxylamine Sulphate	0.612 kg.
A2398	Dipped Belting Fabrics (EP) (conveyor Duck / Synthetic Fabrics of Nylon 6/66 & Polyester 840 denier & above 28:72	1 MT	1. Polyester Industrial Yarn	745 kg
			2. Relevant Industrial Yarn (Nylon 6/66)	305 kg
			3. V.P. Latex	65 kg
			4. Resorcinol	7 kg
			5. Formaldehyde	10 kg
			6. Bonding Agent (Grill bond / coca Bond vulce Bond-E)	5 kg
A2399	Diphenyl Isodecyl Phosphite (DPOP)	1 kg	1. Phenol	0.558 kg.
			2. Isodecyl Alcohol	0.419 kg.
A2400	C-8 ( 3-Hydroxy Naphthalene-2 Carbonyl -( 3 Morpholine - Propyl-Amine)	1 kg	1. 4- (3 Amino Propyl) Morpholine	0.600 kg.
			2. BON Methyl Ester	0.841 kg
A2401	(S)-Valine-Cyclic Urea (Wing B)	1 kg	1. (L)-Valine or (S) Valine	1.837 kg.
			2. Aerylonitrile	0.95 kg.
			3. Methyl Chloroformate	2.25 kg.
A2402	Potassium Pyro Antimonate	1 kg	1. Antimony Trioxide	0.978 kg.
			2. Potassium Hydroxide	0.300 kg.

Annexure "C" to the
Public Notice No.51
Dated: 01/03/2000

ENGINEERING PRODUCTS

Sl.No.	Item of Export	Qty.	Item of Import	Qty. Allowed
C1501	Low Carbon Ferro Manganese	1 MT	1. Aluminium Ingot/ Aluminium Powder	500 kg.
C1502	Medium Carbon Ferro Manganese	1 MT	1. Aluminium Ingot/ Aluminium Powder	250 kg.
C1503	Continuous Cast Copper Rod/ Cathodes	1 MT	1. Copper concentrate	1.06 MT/MT of Copper content in the export product.
C1504	Cold Rolled Non Grain oriented Silicon electrical Steel Sheets/ coils in fully/ semi processed state.	1000 kg.	1. Hot Rolled Alloy Steel Coils	1125 kg.
			2. Organic Coating/ Inorganic Coating	5 kg.
			3. Pickling Oil	0.5 kg.
			4. Steel Stripping	As per packing policy
			5. VCI Rusto paper	As per packing policy
C1505	Hermatic Compressor	1 No.	1. Relevant Valve Plate	1 No.
			2. Relevant Gas pump assembly	1 No.
			3. Crankshaft Assembly	1 No.
			4. Suction Valve	1 No.
			5. Discharge Valve	1 No.
			6. Cylinder Head	1 No.
			7. Stator	1 No.
			8. PTC Relay below 7 AMP	1 No.
			9. Bi-metal thermostat/ motor protector	1 No.
C1506	Identifiable ready- to-use machined parts/ components made wholly or predominantly of Carbon Steel/Non Alloy Steel (not less than 90% by weight) manufactured through forging process, not elsewhere specified.	1 kg.	1. Forging Quality Carbon Steel/ Non Alloy Steel Bars/ Rods/ Billets/ Blooms/ Ingots (Relevant Material)	1.60 Kg/kg content in export
			2. Chemicals Rust Preventing Oil/ Primer/ Paints	2% of the FOB value of export
			3. Miscellaneous items: Refractory material, Die Steel/ Die Blocks, Cutting Tools, Cutters Sawing Blades including bimetallic Bandsaw blades steel shots, fuel oil, heat treatment chemicals, quenching oil and lubricants.	4% of the FOB value of exports.
C1507	Identifiable ready to use machined parts/ components made wholly or predominantly of Alloy Steel/ Stainless Steel (not less than 90% by weight) manufactured through forging process, not elsewhere specified.	1 kg	1. Forging Quality / Alloy Steel/Stainless Steel Bars/ Rods/ Billets/ Blooms/Ingots (Relevant Material)	1.60 kg/kg content in export
			2. Chemicals: Rust Preventing Oil/ Primer Paints	2% of the FOB value of exports
			3. Miscellaneous items: refractory material, Die Steel/ Die Blocks Cutting Tools, Cutters, Sawing Blades including bimetallic Bandsaw blades steel shots, fuel oil, heat treatment chemicals, quenching oil and lubricants.	4% of the FOB value of exports
C1508	Identifiable ready to use machined parts/ components made wholly or predominantly of Iron(not less than 90% by weight) manufactured through casting process, not elsewhere specified.	1 kg	1. Pig Iron	1.25 kg
Note: The above norms are for the export product wholly made of Pig iron. For the export product constituting Pig Iron less than 100% and upto 90% by weight, the import requirement of Pig iron shall be proportionately reduced.
C1509	Identifiable ready to use machined parts/ components made wholly or predominantly of Carbon Steel / Non Alloy Steel (not less than 90% by weight) manufactured through Casting Process, not elsewhere specified.	1 MT	1. Major Raw materials comprising of : Carbon Steel / Non-Alloy Steel Melting Scrap	1700 kgs.
			2. Additives comprising of: a) Core Wire/Scrap/ Ingots/Shots of Aluminium b)Core Wire/Lumps Powder of Calcium Silicide (CaSi) c) Lumps / Powder of Misch Metal d) Ferro Silicon e) Ferro Manganese	50 kgs
			3. Miscellaneous items: a) i) Resin Coated Sand	450 kgs
			3. a) ii) Organic binders	200 kgs.
			3. b) i) Graphite electrode	7.5 kgs.
			3. b) ii) Welding Electrode	12.5 kgs.
			3. b) iii) Mould Wash/ Mould coat	31 kgs.
			3. b) iv) Grinding Wheel	6 kgs.
			3. b) v) Refractories: a) Porous Plugs/Seat Blocks/ Sleevers/ Slide Gate Plates b) Direct Bonded Basic Bricks c) Monolithic/ Gunning/ Ramming/ Castables d) Dolomite/ Magnesia Carbon Bricks	37.5 kgs.
			3. b) vi) Industrial X- Ray Film (Various Grades for Gamma Rays Iridium 192 & Cobalt 60)	9440 Sq.Cm.
			4. Furnace Oil/ Diesel Oil for i) Ladle heating ii) Moulding Heating iii) Heat Treatment	265 Ltrs.
Note 1. : The above norm is applicable only if the export products are manufactured through electric Arc Furnace / Induction Finance Route using melting Scrap as shown at item No. 1(a). 2 : In case the products are manufactured through the Induction Furnace Route, the item 3(b) (i) will not be allowed. 3 : The above norms are for the export product wholly made of Non Alloy Steel. For the export product constituting less than 100% and upto 90% No Alloy Steel by weight, the import requirements of import items at Sl. No. 1 to 3 shall be proportionately reduced.
C1510	Identifiable ready to use machined parts/ components made wholly or predominantly of Alloy Steel ( other than Stainless Steel) (not less than 90% by weight) manufactured through Casting Process, not elsewhere specified.	1 MT	1. Major Raw Materials comprising of: a) Non-Alloy Steel Melting Scrap	1594 kgs.
			1. b) Ferro Alloys comprising of: i) Charge Ferro Nickel/ Nickel Oxide Sinter OR	75 kgs.
			1. b) i) Nickel	30 kgs.
			1. b) ii) Ferro Chrome	21 kgs.
			1. b) iii) Ferro Manganese	25 kgs.
			1. b) iv) Ferro Molybdenum	31 kgs.
			1. b) v) Ferro Silicon	25 kgs.
			2. Additives comprising of: a) Core wire/Scrap / Ingots / shots of Aluminium b) Calcium silicide (CaSi) c) Selenium d) Lumps/Powder of Misch Metal	6 kg
			3. Miscellaneous items a) i) Resin coated Sand	450 kg
			3. a) ii) Organic binders	200 kg
			3. b) i) Graphite Electrode	7.5 kg
			3. b) ii) Welding electrode	12.5 kg
			3. b) iii) Mould Wash/ Mould Coat	31 kg
			3. b) iv)Grinding Wheel	6 kg
			3. b) v) Refractories a) Porous Plugs/ Seat Blocks/ Sleeves/ Slide Gate Plates b) Direct Bonded Basic Bricks c) Monolithic/ Gunning/ Ramming/ Castables d) Dolomite / Magnesia Carbon Bricks	37.5 kg
			3. b) vi) Industrial X-Ray Film (various Grades for Gamma Rays Iridium 192 & Cobalt 60)	9440 Sq. cm.
			4. Furnace Oil/ Diesel Oil for i) Ladle Heating ii) Mould Heating iii) Heat treatment	265 Ltrs.
C1511	Identifiable ready to use machined parts/ components made wholly or predominantly of Stainless Steel (not less than 90% by weight) manufactured through Casting Process, not elsewhere specified.	1 MT	1. Major Raw Materials comprising of: a) Stainless Steel Melting Scrap	862.5 kg
			1. b) Iron Flakes/ Pure Iron/ Iron Powder	387.5 kg.
			1. c) i) Ferro Chrome ii) Charge Nickel Oxide Sinter/ Ferro Nickel OR	400 kg.
			1. c) i) Ferro Chrome	87.5 kg.
			1. c) ii) Nickel	125.0 kg.
			1. c) iii)Ferro Manganese	12.5 kg.
			1. c) iv) Ferro Molybdenum	62.5 kg.
			1. c) v) Ferro Silicon	25 kg.
			2. Additives comprising of: a) Core wire/Scrap/ Ingots/ shots of Aluminium b) Core wire/ Ingots/ powder of Calcium silicide (CaSi) c) Selenium d) Lumps/Powder of Misch Metal	6.25 kg.
			3. Miscellaneous items a) i) Resin coated Sand	1562.5 kg.
			3. a) ii) Organic binders	200 kg.
			3. b) i) Graphite Electrode	7.5 kg.
			3. b) ii) Welding electrode	12.5 kg.
			3. b) iii) Mould Wash/ Mould Coat	31.25 kg.
			3. b) iv)Grinding Wheel	6.25 kg.
			3. b) v) Refractories a) Porous Plugs/ Seat Blocks/ Sleeves/ Slide Gate Plates b) Direct Bonded Basic Bricks c)Monolithic/ Gunning/ ramming/ Castables d) Dolomite / Magnesia Carbon Bricks	37.5 kg.
			3. b) vi) Industrial X-Ray Film (various Grades for Gamma Rays Iridium 192 & Cobalt 60)	9440 Sq.cm.
			4. Furnace Oil / Diesel Oil for i) Ladle Heating ii) Mould Heating iii)Heat Treatment	265 Ltr.
Note:1.The above norm is applicable only if the export product are manufactured through Electric Arc Furnace/ Induction furnace Route using Melting Scrap as shown at item No. 1(a) 2. : In case the products are manufactured through the induction FurnaceRoute, the item 3 (b) (i) will not be allowed. 3. : The above norms are for the export product wholly made of Stainless Steel. For the export product constituting Stainless Steel less than 100% and upto90% by weight, the input requirements of import items at Sr. No. 1 to 3 shall be proportionately, reduced.
C1512	Refrigerator Display Cabinet (Capacity to be Indicated)	1 No.	1. Electro Galvanised Steel sheets pre-painted 0.5 mm thick	1.03 kg/kg content in the export product
			2. Relevant Stainless steel sheet 0.4 mm thick	1.03 kg/kg content in the export product
			3. ABS/HIF with GPPS (General Purposel poly sheets)	1.03 kg/kg content in the export product
			4. Polyurethane foam chemical total foam weight:- a) Polyol	1.03 kg/kg of content in the export product
			4. b) Isocyanate	1.03 kg/kg of content in the export product
			4. c) Cyclo-pentane	1.03 kg/kg of content in the export product
			5. Relevant Hermetically sealed compressors	one set on net to net
			6. Relevant Fan Motors a) Evaporator cooling	on net to net basis
			6. b) Compressor/ condensor cooling	on net to net basis
			7. Relevant thermostate	1 No.
			8. Copper tube 6.350x0.6 mm thick	1.03 kg/kg of content in the export product
			9. Copper capillary tube	1.03 kg/kg of content in the export product
			10. Relevant Filter Drier(Copper)	1 No.
			11. Relevant Evaporator (cu tube, A1 fin)	1 No.
			12. Relevant Condensor (cu tube, A1 fin)	1 No.
C1513	Pneumatic Tool-Clay Digger (Picks) with outside Trigger, Throttle Latch Retainer	1 No.	1. Relevant Air Inlet Nipple	1 No.
			2. Relevant Head Bolt	1 No.
			3. Relevant Piston	1 No.
			4. Relevant Cylinder	1 No.
			5. Relevant Fronthead	1 No.
			6. Relevant Throttle Valve	1 No.
			7. Relevant Latch Retainer Bolt	1 No.
			8. Relevant Valve Block	1 No.
			9. Relevant Valve	1 No.
			10. Relevant Chuck bushing	1 No.
			11. Relevant Retainer-Latch	1 No.
			12. Relevant Lever-Throttle Valve	1 No.
			13. Relevant Handle Assembly	1 No.
			14. Relevant Latch Ret Bolt Bushing	1 No.
Note : The import of components shall be allowed on net to net basis with accountability clause.
C1514	Pneumatic Tool-Light Simplate Valve Temper with Bore and Stroke size 17/16" X 6" (36.5mm X 152.45 mm)	1 No.	1. Relevant Elbow	1 No.
			2. Relevant Air Strainer	1 No.
			3. Relevant throttle valve Lever	1 No.
			4. Relevant throttle Valve Body	1 No.
			5. Relevant throttle Valve	1 No.
			6. Relevant Nipple	1 No.
			7. Relevant Cylinder Head Assembly	1 No.
			8. Relevant Oil Regulating Plug	1 No.
			9. Relevant Upper Valve case Lid	1 No.
			10. Relevant Valve case	1 No.
			11. Relevant Lower Valve case lid	1 No.
			12. Relevant Exhaust Deflector	1 No.
			13. Relevant Piston with Plug Assembly	1 No.
			14. Relevant Cylinder	1 No.
			15. Relevant Retainer Nut	1 No.
			16. Relevant Retainer	1 No.
			17. Relevant Piston Rod Bushing	1 No.
			18. Relevant Piston PKG	1 No.
			19. Relevant Piston Bushing	1 No.
			20. Relevant Aluminium Butt	1 No.
			21. Relevant Lock nut	1 No.
Note : The import of components shall be allowed on net to net basis with accountability clause.
C1515	Pneumatic Tool- Heavy duty Ring volve Temper with Bore and Stroke size upto 2 1/4" X 6" (two and quarter inch X six inch) (57.2mm X 152 mm)	1 No.	1. Relevant Streat Elbow	1 No.
			2. Relevant Air Strainer	1 No.
			3. Relevant Throttle Valve Lever	1 No.
			4. Relevant Throttle Valve Body	1 No.
			5. Relevant throttle Valve	1 No.
			6. Relevant Nipple	1 No.
			7. Relevant Cylinder Head Assembly	1 No.
			8. Relevant Valve Lid	1 No.
			9. Relevant Valve	1 No.
			10. Relevant valve Box	1 No.
			11. Relevant Lock Clip	1 No.
			12. Relevant Exhaust Clip	1 No.
			13. Relevant Piston with Plug Assembly	1 No.
			14. Relevant Cylinder & Bushing Assembly	1 No.
			15. Relevant Piston Packing	1 No.
			16. Relevant Lock Clip	1 No.
			17. Relevant Piston Gland nut	1 No.
			18. Relevant Piston Gland Sleeve	1 No.
			19. Relevant Butt	1 No.
			20. Relevant Lock Nut	1 No.
Note : The import of component shall be allowed on net to net basis with accountability clause.
C1516	Pneumatic Tool- Rammer	1 No.	1. Relevant Valve	1 No.
			2. Relevant Throttle valve lever	1 No.
			3. Relevant Throttle Valve Bushing	1 No.
			4. Relevant Cylinder Head	1 No.
			5. Relevant Upper Valve Case Lid	1 No.
			6. Relevant Valve Case	1 No.
			7. Relevant Lower Valve Case Lid	1 No.
			8. Relevant Piston & Plug Assembly	1 No.
			9. Relevant Cylinder & Bushing Assembly	1 No.
			10. Relevant Bushing	1 No.
			11. Relevant Piston Packing	1 No.
			12. Relevant Piston Bushing	1 No.
			13. Relevant Check Nut	1 No.
			14. Relevant retainer	1 No.
			15. Relevant Rubber Butt	1 No.
Note : The import of components shall be allowed on net to net basis with accountability clause.
C1517	Pneumatic Tool Clay Digger round (picks) with outside trigger Sleeve Retainer and round/Square Chuck	1 No.	1. Relevant Cylinder	1 No.
			2. Relevant Sleeve	1 No.
			3. Relevant Handle & Bush Assembly	1 No.
			4. Relevant Lever	1 No.
			5. Relevant Lever Pin	1 No.
			6. Relevant Throttle Valve	1 No.
			7. Relevant Retainer sleeve	1 No.
			8. Relevant Valve	1 No.
			9. Relevant Piston	1 No.
			10. Relevant Upper Valve Case Lid	1 No.
			11. Relevant Lower Valve Case Lid	1 No.
			12. Relevant Valve Case	1 No.
			13. Relevant Back Head Bolt	2 Nos.
Note : The import of components shall be allowed on net to net basis with accountability clause.

Note: Though every effort has been made to make this a replica of the original Public Notice, errors might still occur. In case of doubts, please refer the original.

Presented by eximkey.com